dtoverlays: Add overlay for imx355 image sensor

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Author: 6by9

arch/arm/boot/dts/overlays/Makefile

@@ -142,6 +142,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
 	imx296.dtbo \
 	imx327.dtbo \
 	imx335.dtbo \
+	imx355.dtbo \
 	imx378.dtbo \
 	imx415.dtbo \
 	imx462.dtbo \

arch/arm/boot/dts/overlays/README

@@ -2977,6 +2977,24 @@ Params: orientation             Sensor orientation (0 = front, 1 = rear,
                                 Module (1, 3, 4, or 5) or Pi 5.
 
 
+Name:   imx355
+Info:   Sony IMX355 camera module.
+        Uses Unicam 1, which is the standard camera connector on most Pi
+        variants.
+Load:   dtoverlay=imx355,<param>
+Params: orientation             Sensor orientation (0 = front, 1 = rear,
+                                2 = external, default external)
+        rotation                Mounting rotation of the camera sensor (0 or
+                                180, default 0)
+        media-controller        Configure use of Media Controller API for
+                                configuring the sensor (default on)
+        cam0                    Adopt the default configuration for CAM0 on a
+                                Compute Module (CSI0, i2c_vc, and cam0_reg).
+        4lane                   Enable 4 CSI2 lanes. This requires a Compute
+                                Module (1, 3, 4, or 5) or Pi 5.
+        vcm                     Configure a VCM focus drive on the sensor.
+
+
 Name:   imx378
 Info:   Sony IMX378 camera module.
         Uses Unicam 1, which is the standard camera connector on most Pi

arch/arm/boot/dts/overlays/imx355-overlay.dts

@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Definitions for IMX355 camera module on VC I2C bus
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+/{
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2c0if>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	clk_frag: fragment@1 {
+		target = <&cam1_clk>;
+		__overlay__ {
+			status = "okay";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c0mux>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	i2c_frag: fragment@100 {
+		target = <&i2c_csi_dsi>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			#include "imx355.dtsi"
+
+			vcm: ad5398@c {
+				compatible = "adi,ad5398";
+				reg = <0x0c>;
+				status = "disabled";
+				VANA-supply = <&cam1_reg>;
+			};
+		};
+	};
+
+	csi_frag: fragment@101 {
+		target = <&csi1>;
+		csi: __overlay__ {
+			status = "okay";
+
+			port {
+				csi_ep: endpoint {
+					remote-endpoint = <&cam_endpoint>;
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
+				};
+			};
+		};
+	};
+
+	fragment@102 {
+		target = <&csi1>;
+		__dormant__ {
+			compatible = "brcm,bcm2835-unicam-legacy";
+		};
+	};
+
+	fragment@201 {
+		target = <&csi_ep>;
+		__dormant__ {
+			data-lanes = <1 2 3 4>;
+		};
+	};
+
+	fragment@202 {
+		target = <&cam_endpoint>;
+		__dormant__ {
+			data-lanes = <1 2 3 4>;
+			link-frequencies =
+					/bits/ 64 <360000000>;
+		};
+	};
+
+	__overrides__ {
+		rotation = <&cam_node>,"rotation:0";
+		orientation = <&cam_node>,"orientation:0";
+		media-controller = <0>,"!102";
+		cam0 = <&i2c_frag>, "target:0=",<&i2c_csi_dsi0>,
+		       <&csi_frag>, "target:0=",<&csi0>,
+		       <&clk_frag>, "target:0=",<&cam0_clk>,
+		       <&cam_node>, "clocks:0=",<&cam0_clk>,
+		       <&cam_node>, "avdd-supply:0=",<&cam0_reg>,
+		       <&vcm>, "VANA-supply:0=", <&cam0_reg>;
+		vcm = <&vcm>, "status=okay",
+		      <&cam_node>,"lens-focus:0=", <&vcm>;
+		4lane = <0>, "+201+202";
+	};
+};
+
+&cam_node {
+	status = "okay";
+};
+
+&cam_endpoint {
+	remote-endpoint = <&csi_ep>;
+};

arch/arm/boot/dts/overlays/imx355.dtsi

@@ -0,0 +1,26 @@
+// Fragment that configures an imx355
+
+cam_node: imx219@1a {
+	compatible = "sony,imx355";
+	reg = <0x1a>;
+	status = "disabled";
+
+	clocks = <&cam1_clk>;
+	clock-names = "xclk";
+
+	avdd-supply = <&cam1_reg>;	/* 2.8v */
+	dvdd-supply = <&cam_dummy_reg>;	/* 1.8v */
+	dovdd-supply = <&cam_dummy_reg>;/* 1.2v */
+
+	rotation = <180>;
+	orientation = <2>;
+
+	port {
+		cam_endpoint: endpoint {
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+			link-frequencies =
+				/bits/ 64 <444000000>;
+		};
+	};
+};