Support New iCue Commander Core?

[JoseArtunedo]

Thank you first of all, for your great project, its potential is undeniable.

Will support be added for the new Icue Commander Core?

https://www.amazon.es/gp/product/B08G1Q3GZR?psc=1

I was investigating, and I have not seen a trace, but the temperature sensors could be included in the arduino code or it is not possible.

Thank you

[Legion2]

The link does not work and I can't find any reference for the iCue Commander Core.

[kostyamat]

Hello. Please tell me which type of thermistors is suitable for Commander Pro?
Will this work?
€ 0,83 | 5PCS/LOT Thin Film Thermistor ntc 10k 1% 25mm SMD 103 Membrane Temperature Sensor for 3D Printer Termistor
https://a.aliexpress.com/_BTrsYz

[Legion2]

10 k ohm Thermistor should work

[JoseArtunedo]

El enlace no funciona y no puedo encontrar ninguna referencia para el iCue Commander Core.

I do not know why the link I sent cannot be displayed. I leave you another.

Also adding the diagram of connections.

https://www.corsair.com/es/es/Categor%C3%ADas/Productos/Accesorios-%7C-Piezas/Commander-CORE-RGB-&-PWM-Fan-Controller/p/CW-8960071

[JoseArtunedo]

Hola. Dígame qué tipo de termistores es adecuado para Commander Pro.
esto funcionara?
€ 0,83 | 5 unids / lote termistor de película delgada ntc 10k 1% 25mm SMD 103 Sensor de temperatura de membrana para termistor de impresora 3D
https://a.aliexpress.com/_BTrsYz

Great this info comes to me, I was also looking for and had the doubt if they were 10K, I had the original commander pro at home, I measured and if they are 10k to work.

[Legion2]

I think it should be possible to support the Commander Core, now only the USB PID is required, so iCUE will detect it.

[JoseArtunedo]

I think so, it's basically an all-in-one commander pro + Lighting Node Core. It will simplify everything to the maximum. With this, it is simply all you need to be able to control PWM and lighting from the same place.

The USB PID, is taken from an original controller, or what is the way to obtain it?

[Legion2]

The features of a commander core can already be realized with this library, just combine the commander pro and the MultipleFans example.

The USB PID can be obtained from the original device or by guessing it.

[JoseArtunedo]

I am waiting to receive a Corsair iCUE H150i ELITE CAPELLIX, which contains the Commander Core, if you explain to me how I can obtain or know the USB Pid I will provide it to you. Is this part I do not know how to do it, I have the basic knowledge of arduino and programming

[Spegs21]

I am waiting to receive a Corsair iCUE H150i ELITE CAPELLIX, which contains the Commander Core, if you explain to me how I can obtain or know the USB Pid I will provide it to you. Is this part I do not know how to do it, I have the basic knowledge of arduino and programming

Have you found the PID yet? You can use HWiNFO or just device manager to find the PID. In HWiNFO, expand Ports->USB in the device tree. Then expand all of the USB controllers and hubs until you find the Commander Core. PID is listed in the Hardware ID line. It'll look like:

Hardware ID: USB\VID_1B1C&PID_1B2D

[z0rlac]

Using USBDeview, here is the information from my Commander Pro attached to a H150i Capellix

Device Name: CORSAIR iCUE Commander CORE
PID: USB\VID_1B1C&PID_0C1C<device serial number here>

[Legion2]

Device Name: CORSAIR iCUE Commander CORE
PID: USB\VID_1B1C&PID_0C1C

Looks good, I will try this weekend to create a sketch for the commander core.